Safety rules for painting lines
Major hazards: mechanical damage, light radiation damage, fire hazard, etc. Before working: Check the compressed air switch should be open, around the machine and the conveyor belt should be no work and debris. To confirm the normal and then closed start. After the start of a single station in order to start a single device, found to start or sound abnormalities should be shut down to check whether there is a switch or lack of equality, troubleshooting before work.
At work
1, after the operation of the machine should observe the control cabinet lights and instrument display is within the normal range, check the electrical, motor overheating, noise and other anomalies, in any case can not reach into the equipment is running. Find the problem should stop or repair the repair.
2, on the move, remove the heavier parts, to take more people lift or first put on a special table and then flip the way to prevent the workpiece fell injured. Gun moving when people can not move within the scope to prevent bruises, spray paint landing gear, are not allowed to enter, to prevent the landing gear when the pressure of people, squeeze hands.
3, the oven in addition to special circumstances, are not allowed to manually operate the tray movements, the alarm should be identified after the failure to reset.
4, UV lamp work with strong ultraviolet rays, hands can not touch, eyes can not look directly to prevent burns. When the temporary shutdown should be confirmed whether the UV lamp flip up, work and after the shutdown to see if there is a workpiece under the lamp, if the workpiece should be promptly removed to prevent baking.
5, demolition of paint pump or spray gun should be closed before the gas source, pressure relief and then.
6, electrical appliances can not be placed before the cabinet and debris, wiping the panel and the top of the cabinet every week, the control cabinet filter once a week to remove the dust.
After work:
Check the machine with or without retention of the workpiece; site clean, the remaining paint and thinner should be sealed sealed storage, the machine has been closed air compressor switch, the control cabinet has been powered off, to confirm no problem before leaving. In case of emergency: should immediately stop by emergency stop button, take correct measures to prevent accidents to expand. If someone is injured immediately rescue; if the fire immediately shouting the alarm, while fighting the primary fire, if you can not control the evacuation plan immediately by fire, and report the monitor or security officer and other leaders.
Major hazards: mechanical damage, light radiation damage, fire hazard, etc. Before working: Check the compressed air switch should be open, around the machine and the conveyor belt should be no work and debris. To confirm the normal and then closed start. After the start of a single station in order to start a single device, found to start or sound abnormalities should be shut down to check whether there is a switch or lack of equality, troubleshooting before work.
At work
1, after the operation of the machine should observe the control cabinet lights and instrument display is within the normal range, check the electrical, motor overheating, noise and other anomalies, in any case can not reach into the equipment is running. Find the problem should stop or repair the repair.
2, on the move, remove the heavier parts, to take more people lift or first put on a special table and then flip the way to prevent the workpiece fell injured. Gun moving when people can not move within the scope to prevent bruises, spray paint landing gear, are not allowed to enter, to prevent the landing gear when the pressure of people, squeeze hands.
3, the oven in addition to special circumstances, are not allowed to manually operate the tray movements, the alarm should be identified after the failure to reset.
4, UV lamp work with strong ultraviolet rays, hands can not touch, eyes can not look directly to prevent burns. When the temporary shutdown should be confirmed whether the UV lamp flip up, work and after the shutdown to see if there is a workpiece under the lamp, if the workpiece should be promptly removed to prevent baking.
5, demolition of paint pump or spray gun should be closed before the gas source, pressure relief and then.
6, electrical appliances can not be placed before the cabinet and debris, wiping the panel and the top of the cabinet every week, the control cabinet filter once a week to remove the dust.
After work:
Check the machine with or without retention of the workpiece; site clean, the remaining paint and thinner should be sealed sealed storage, the machine has been closed air compressor switch, the control cabinet has been powered off, to confirm no problem before leaving. In case of emergency: should immediately stop by emergency stop button, take correct measures to prevent accidents to expand. If someone is injured immediately rescue; if the fire immediately shouting the alarm, while fighting the primary fire, if you can not control the evacuation plan immediately by fire, and report the monitor or security officer and other leaders.