â— Caring for trucks, technical maintenance
First of all, we should always care about the maintenance of the car and humane maintenance, like the car, and people do not get the most concerned about the maintenance, it will not play the best condition, to do regular maintenance, every day, every maintenance Before the second trip, you should insist on checking the vehicle's oil, tire pressure, running long-distance oil does not need to be too much, preferably in the oil caliper's dimensions, the tire pressure is actually very critical, so we must carefully check the tire pressure, observe there After eating without a fetus, you can use a screwdriver to knock out the small stones in the tire joints. The stones in the tire joints will not only make a terrible noise on the road, but will also directly affect our fuel consumption.
â— adjust the shroud to reduce wind resistance
Adjust the height of the car's shroud, after all, our mileage is thousands of kilometers. Of course, the van does not need to be adjusted every time, but it should also be checked frequently, because if the shroud is loose, it will also affect the driving. After checking the car, it is better to adjust the angle of the rearview mirror and the seat before starting, so as to avoid adjustment during driving, it is unsafe to drive.
â— start operation details, save less
Starting fuel consumption can not be ignored, because there are some factors such as traffic jams, toll stations, etc. that will lead you to have to start numerous times, so this is also a fuel-efficient details, and some people are like starting at the start , this will undoubtedly waste a large part of the oil, should be added to the highest gear with the shortest throttle time, the automatic transmission is switched to manual mode and added to the 7-speed automatic mode, if it is the car you have been driving You know the throttle and power it needs, so only if you control it well, you can save it. Not too few, fuel saving is always the process of accumulating more,
For Volvo automatic transmission, I usually use the manual mode is flat road, first select the automatic mode and then converted to manual mode, see the general speed of 1000 rpm to increase the file, if you have not had time to add a plus 2 files After the 7th gear is converted to the automatic mode, the slow control of the throttle slowly and slowly makes it easily added to the 12th gear. From the 10th gear to the 11th gear to the 12th gear, the speed is relatively slow, and the throttle is increased. Not much use, so slowly increase it up to 12 files. General start to 12 speed to 75, fuel consumption does not exceed 1 liter. Poor operation may require 2 liters or more, so you can think about how many times you have to start a long journey. There are traffic jams at the toll booths. Everyone is used to seeing such scenes. If everyone is in the same order as the following, it may not be so irritating. It will not make your fuel consumption even higher, but there are At the toll booths, there are some cars that are constantly on the left and right sides, so that you can't be guarded. To compete with them is no doubt that wasting more oil will not save time.
Reasonable use of cruise adjustment
In the plain road conditions, as much as possible after the speed up to use the cruise, of course, have to observe the road conditions and instruments after cruising, see the moment the fuel consumption changes at the beginning, the engine sound began to change, then you have to cancel the cruising, because of possible road conditions Changes have taken place, resulting in the need for more power to maintain the current speed, so after this conversion, use a small throttle to give oil, even if there is a slight change in speed, when a short period of time after the refueling to lift up the speed, do not resume cruising, the cruising The switch is turned on and the speed is mentioned. The speed you want to cruise is slightly higher. Then press the minus switch to activate the cruise. When activated, the engine will not run at high speed. Therefore, reasonable use of the cruise can be more fuel-efficient if the traffic conditions permit. .
Driving on the roads in the hilly areas cannot be cruising. This will undoubtedly increase fuel consumption. When driving on hilly roads, you will encounter relatively flat slopes when you have a wide line of sight. When the slope is properly refueled, keep it on the slope, quickly climb the slope to the top of the hill and slowly lift the throttle slowly, let the inertia send it to the next slope, and restore it just after finishing the slope and going to the previous slope. The action slowly toes the accelerator pedal with a toe. This will allow you to use less fuel on hilly roads.
According to the different flow directions of heating steam and feed liquid, the operation flow of continuous evaporation crystallizer can be divided into countercurrent method, downstream method, cross-flow method and advection method. In addition to these four processes, other processes may be arranged according to the production situation. Sometimes in most of the evaporation, for example, every effect is not to create a effect after the secondary steam are introduced and used as heating steam, but will be part of the secondary steam used for preheating material liquid into the first effect of the derivation, or other has nothing to do with the evaporation of heating process, the rest is still after entering a valid heating steam, is referred to as the additional steam that part of the steam.
MVR Continuous Evaporative Crystallizer
MVR Continuous Evaporative Crystallizer , also known as multi-effect evaporator, is suitable for sodium chloride, phenylpropanium acid, sodium sulfate, ammonium chloride, ammonium glycolic acid; barium chloride ,zinc sulfate, calcium chloride, ammonium, sodium hydroxide and other materials evaporation and crystallization.
Product features
1. this equipment is mainly for targeted materials evaporation concentrate, And turn final product into a certain size of solid crystal.
2. When liquid material pass through circulation pump it heats up and direct into evaporation separator, it has a better result in vapor liquid separation.
3. Compact structure uses less area occupancy, stable performance etc
4. Easy to operate, easy maintenance.
5. It has sufficient mechanical strength and less metal consumption. According to characteristics of material and evaporation capacity, it can be designed in a single-effect or multi-effect unit. This device is mainly applicable for liquid that precipitated crystals. Mainly used in chemical industry, Metal minings melting, Steel mills waste washing, Power plant`s wet desulfurization waste dispose and so on. In view of characteristics and complexity of various solutions, our company will make specific technical solutions for customers to choose.
Energy Saving
The purpose of multi-effect evaporation is to use secondary steam in evaporation process to save steam consumption to improve economic efficiency. The following chart is the amount of heating steam consumed by per kilogram of water, in which the actual consumption includes various heat losses during evaporation, its value changes slightly with different evaporator and evaporation process.
Energy Saving Crystallization Evaporator,Stable Continuous Evaporative Crystallizer,Mechanical Multi-Effect Crystallization Evaporator,Stainless Steel Evaporative Crystallizer
Yangzhou Tongyang Chemical Equipment Co., Ltd. , https://www.tyceqt.com