China-Pellet-Dehumidifier-Dryer-Dehumidifying-Drying-Loader

STANDARD CONFIGRAUTION
♦ Adopts P.I.D. temperature controller to accurately control regenerative temperature
♦ The dehumidifying system of the series feature two coolers to ensure a low return air temperature and low dew-point
♦ Return air filter is mounted inside to ensure no contamination t the honeycomb.
♦ Full molecular sieve, providing better honeycomb dehumidification than silica gel application.

OPTIONAL
♦ Centralized automatic control can be realized by optionally selected PLC touch screen controller.
♦ Optionally select dew-point monitor to realize dew-point real - time monitoring.
♦ Optionally select drying heater and its temp.controller to work with drying hopper for material dehumidifying
and drying.
♦ Optional heat-resistant air pipe,cyclone dust separator with floor stand,oil filter are available.
♦ Dew-point temperature at -50ºC can be set.

SPECIFICATION
Model XDD-25/50 XDD-50/50 XDD-50/80 XDD-75/80 XDD-75/120 XDD-100/120 XDD-100/150 XDD-150/150 XDD-200/200 XDD-200/300
Hopper(L) 25 50 50 75 100 100 150 200 200 300
Dehumidification(m³/hr) 50 50 80 80 120 150 150 200 200 200
Drying(kw) 0.4 0.4 0.5 0.75 1.1 1.5 1.5 2.2 2.2 2.2
Regeneration blower(kw) 0.2 0.2 0.2 0.2 0.2 0.2 0.2 0.4 0.4 0.4
Drying heater(kw) 3.6 3.6 3.6 3.6 5.4 5.4 6 12 12 15
Regeneration heater(kw) 2.4 2.4 3.6 3.6 3.6 3.6 3.6 5.4 5.4 5.4
Feeding blower(kw) 0.75 0.75 0.75 0.75 0.75 0.75 0.75 1.5 1.5 1.5
Feeding pipe(inch) 11/2" 11/2" 11/2" 11/2" 11/2" 11/2" 11/2" 11/2" 11/2" 11/2"
Vacuum hopper(L) 6 6 6 6 6 6 6 6 12 12
Photosensor hopper(L) 6 6 6 6 6 6 6 6 12 12
W(mm) 1150 1150 1300 1300 1300 1300 1350 1350 1350 1350
D(mm) 650 650 790 790 790 790 790 790 790 790
H(mm) 1550 1550 1850 1850 1850 1850 1850 2000 2200 2200
Net.(kg) 320 344 375 385 405 442 449 475 560 585

DRYING CAPACITY SPECIFICATION
 
DEW-POINT SYNOPSIS
Raw material Humidity Drying(hr) Specific heat Density(kcal/kg) Material moisture(%) Dehumidificated(%)
ABS 80 2-3 0.34 0.6 0.3 0.02
CA  75 2-3 0.5 0.5 1 0.02
CAB 75 2-3 0.5 0.5 0.8 0.02
CP 75 2-3 0.6 0.6 1 0.02
LCP 150 4 0.6 0.6 0.04 0.02
POM 100 2 0.35 0.6 0.2 0.02
PMMA 80 3 0.35 0.65 0.5 0.02
IONOMER 90 3-4 0.55 0.5 0.1 0.04
PA6/6.5/6.10 75 4-6 0.4 0.65 1 0.05
PA11 75 4-5 0.58 0.65 1 0.05
PA12 75 4-5 0.28 0.65 1 0.05
PC 120 2-3 0.28 0.7 0.3 0.01
PU 90 2-3 0.45 0.65 0.3 0.02
PBT 130 3-4 0.3-0.5 0.7 0.2 0.02
PE 90 2-3 0.55 0.6 0.01 <0.01
PEI 150 3-4 0.6 0.6 0.25 0.02
PET 160 4-6 0.3-0.5 0.85 0.2 0.05
PETG 70 3-4 0.6 0.6 0.5 0.02
PEN 170 5 0.85 0.85 0.1 0.05
PES 150 4 0.7 0.7 0.8 0.02
PMMA 80 3 0.65 0.65 0.5 0.02
PPO 110 1-2 0.4 0.5 0.1 0.04
PPS 150 3-4 0.6 0.6 0.1 0.02
PI 120 2 0.27 0.6 0.4 0.02
PP 90 1 0.36 0.5 0.1 0.02
PS(GP) 80 1 0.28 0.5 0.1 0.02
PSU 120 3-4 0.31 0.65 0.3 0.02
PVC 70 1-2 0.2 0.5 0.1 0.02
SAN(AS) 80 1-2 0.32 0.5 0.1 0.05
TPE 110 3 0.7 0.7 0.1 0.02
 
DRYING CAPACITY (kg/hr)
XD-30H 50H 80H 120H 150H 200H 300H 400H 500H 700H 1000H 1500H
18 27 35 71 105 180 210 275 310 355 425 710
15 22 30 60 90 150 180 220 280 295 355 590
15 22 30 60 90 150 180 220 280 295 355 590
18 28 35 71 105 180 210 240 320 355 425 710
13 20 27 55 80 135 160 290 265 265 320 530
27 40 53 105 160 265 320 350 450 530 640 1060
19 29 38 77 115 192 230 260 320 383 460 767
11 17 22 44 66 111 133 175 200 220 265 443
10 14 19 38 58 96 115 135 178 192 230 383
12 17 23 46 69 115 138 158 200 230 275 460
12 17 23 46 69 115 138 158 200 230 275 460
21 31 41 83 124 206 250 285 345 413 495 826
19 29 39 77 115 190 230 260 315 383 460 767
15 23 31 62 93 155 186 219 268 310 372 620
53 80 106 212 318 531 637 798 985 1062 1275 2125
13 20 27 53 80 133 160 210 243 265 320 530
13 19 25 59 75 125 150 180 220 250 300 500
13 20 27 53 80 133 160 190 225 265 320 530
15 23 30 60 90 150 180 220 260 300 360 600
15 23 30 60 90 150 180 220 260 300 360 600
19 29 38 88 115 190 230 260 315 385 460 765
22 33 44 88 133 220 265 298 355 440 530 885
13 20 27 53 80 133 160 200 228 265 320 530
27 40 53 105 160 265 320 365 453 530 640 1060
44 66 88 180 265 442 530 750 818 885 1060 1770
44 66 88 180 265 442 531 750 818 885 1062 1770
14 22 29 60 85 145 173 198 254 290 345 575
22 33 44 90 135 220 265 315 378 442 530 885
22 33 44 90 135 220 265 315 378 442 530 885
20 30 40 85 125 205 250 298 354 413 495 826

 
WHAT IS " HONEY-COMB"?
The main body of honeycomb rotor is formed by ceramic honeycomb which is made from ceramic fiber
and organic addictive. Molecular sieve and silicone as basic material are crystallized and sintered at high
temperature for hard surface and tightly attached to the internal wall of honeycomb. Therefore,
it would not generate silt as barrel packaged or turntable molecular sieve to contaminate the plastic.
The honeycomb rotor can be used permanently and can be washed, while the ordinary molecular sieve
must be usually replaced for its easily getting saturate and aging. The water of moisture return air will
be quickly absorbed by molecular sieve when it across innumerable ostioles of the honeycomb rotor,

Therefore ,the air is completely dehumidified and reaches a very low dew-point. Regenerating and dehumidifying happen simultaneously and follow the similar principle, except that their regeneration air flows in the opposite direction.
 
WORKING PRINCIPLE
Dehumidification and drying: The hot and humid air from drying material barrel is blown into honeycomb rotor
after cooling. The water in air is absorbed by rotor and then desorbed by the regeneration heating air. The two
airflows workon the rotor at the same time, and as the rotor rotates, the water in air can be absorbed and desorbed continuously. Thus,a stable low dew-point air is formed and then blown into the drying barrel after heated to the
drying temperature of plastic, forming a closed loop to dry material.
Material suction: material suction is to suck material from material barrel or other material container into drying
material barrel. The motor starts to run when the magnetic reed switch of the vacuum hopper detects no material,
generatingvacuum in vacuum hopper, and then the material in material barrel will be sucked into vacuum hopper
because of the pressure difference of air. The motor stops working after sucking and the material will drop into
drying barrel. At last the dried material will be sucked into SVH hopper or other hopper which is set in plastic
moulding machine.

COMPANY PROFILE
         XINGKE , Officially launched the business cooperation with SHINKOR(Korea)in 2016, It has introduced a technician from Korea and focus on development of technologies to be our engineering director,The objective of XINGKE is to make "Technology as the core,customer as the oriented" becomes to solution provider for automation system.

TECHNICAL SUPPORT
      XINGKE has two major production in abroad and China, with a lot of agents , representative offices and four branch in over the world ,set up the leading visualize in molding manufacturing processing.


WHY US ?
* More than 30 years experience in plastic moulding & extrusion industry;
* CE,ROTH,ISO etc. certification exams passed.
* Professional sales team for overseas markets;
* High efficiency, High communicate

PRODUCTS VIEW
* Raw Materials Processing System
* Centralized Drying Dehumidifying System
* One-Stop Solution
* "Euro" Slow-Speed Granulators
* Gravimetric Blenders
* "Euro" Hopper Dryers
* All In One Dehumidifier Dryers
* Honeycomb Dehumidifiers
* Oil Heaters
* Water Cooled Chillers

FAQ
1) Are you manufacturers or trading company ?
X: Manufacturer.We produce machines in China factory and developing products from South Korea for best technical resourses , It can realize to advanced technology and reasonable cost for clients.
2) Do you have CE,EU,ISO9001 etc. certification ?
X:Yes , All of our products approved with these certifications.
3) Do you have any experience in new IMM fatory planning ?
X:Yes, also we can offer you one - stop solution (liquid water ,eletric,vacuum ) for your IMM or extrusion facory. 

 

This entry was posted in on